AMCC 3WARE 9590SE Guía de usuario descargar pdf (Pagina 22)

Chapter 1. Introduction to the 3ware Command Line Interface

16 3ware Serial ATA RAID Controller User Guide

Figure 6. RAID 50 Configuration Example

Single Disk

A single drive can be configured as a unit through 3ware software. (3BM,

3DM 2, or CLI). Like disks in other RAID configurations, single disks

contain 3ware Disk Control Block (DCB) information and are seen by the OS

as available units.

Single drives are not fault tolerant and therefore not recommended for high

availability systems unless additional precautions are taken to prevent system

hangs and data loss.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 109 110

CLI Guide 1
Copyright 2
Trademarks 2
Disclaimer 2
Table of Contents 3
About this CLI Guide 7
Introduction to the 3ware 8
Command Line Interface 8
Supported Operating Systems 9
Terminology 9
Installing the 3ware CLI 10
Run CLI 11
Install Software. If the 11
Working with 3ware CLI 12
Scripting examples 14
Conventions 15
RAID Concepts 16
Available RAID Configurations 17
Single Disk 22
Hot Spare 23
Support for Over 2 Terabytes 25
CLI Syntax Reference 26
Syntax Overview 28
/c1 add type=raid1 disk=0-1 29
Shell Object Commands 30
[force] 34
Controller Object Commands 35
/cx show achip 38
/cx show allunitstatus 38
/cx show autocarve 38
/cx show autorebuild 39
/cx show bios 39
/cx show carvesize 40
/cx show ctlbus 40
/cx show driver 40
/cx show drivestatus 40
/cx show firmware 41
/cx show memory 42
/cx show model 42
/cx show monitor 42
/cx show numports 42
/cx show numunits 43
/cx show ondegrade 43
/cx show pcb 43
/cx show pchip 43
/cx show serial 44
/cx show spinup 44
/cx show stagger 44
/cx show unitstatus 44
show alarms [reverse] 46
show diag 46
show phy 47
show rebuild 47
show selftest 49
show verify 51
Example: type=raid5 52
For the 7/8000 55
rescan [noscan] 56
add rebuild= 58
add verify= 59
Setting Up a Verify Schedule 59
add selftest= 60
set selftest=enable 62
[task=UDMA 62
set carvesize=[1024..2048] 64
set autorebuild=on 64
start mediascan 66
stop mediascan 66
Unit Object Commands 67
/cx/ux show autoverify 69
/cx/ux show cache 69
/cx/ux show identify 69
/cx/ux show ignoreECC 69
/cx/ux show initializestatus 70
/cx/ux show name 70
/cx/ux show qpolicy 70
/cx/ux show rebuildstatus 70
/cx/ux show serial 71
/cx/ux show status 71
/cx/ux show storsave 71
/cx/ux show verifystatus 71
RaidType 79
Migration Process 82
Example of splitting a mirror 83
Example of capacity expansion 83
Example of migrate output 83
Port Object Commands 85
attribute 86
/cx/px show firmware 87
/cx/px show identify 87
/cx/px show lspeed 87
/cx/px show model 87
/cx/px show serial 88
/cx/px show smart 88
/cx/px show ncq 88
remove [noscan] [quiet] 90
Phy Object Commands 91
BBU Object Commands 92
/cx/bbu show serial 94
/cx/bbu show status 94
/bbu show all 95
/cx/ex show controllers 98
/cx/ex/ show diag=helptext 99
/cx/ex show slots 99
/cx/ex show fans 99
/cx/ex show temp 99
show all 100
Example: 102
Enclosure Object Commands 103
Help Commands 104
Help with attributes 105
Command Logging 109
Return Code 109
If you type: 110

Comentarios a estos manuales

Sin comentarios

AMCC 3WARE 9590SE Guía de usuario Pagina 22

Comentarios a estos manuales

Relacionado con productos y manuales para Los controladores raid AMCC 3WARE 9590SE