AMCC 3WARE 9590SE Guía de usuario Pagina 62
- Pagina / 110
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2. CLI Syntax Reference
56 3ware Serial ATA RAID Controller User Guide
The priority of rebuild versus I/O operations is specified with 1..5, where 1 is
more resources and 5 the least. Setting the value to 1 gives maximum
processing time to rebuilds rather than I/O. Setting the value to 5 gives
maximum processing time to I/O rather than rebuilds.
Enabling and disabling rebuild schedules is only for 9000 series controllers,
however the rebuild rate (1..5) applies to all controllers.
7000- and 8000-series controllers have only one setting for Task Rate; it
applies to both rebuild and verify rates. This rate is not persistent following a
reboot for 7000- and 8000-series controllers.
/c
x
set verify=enable|disable|1..5
This command enables or disables all verify background task slots on
controller /cx and (when enabled) sets the priority of verification versus I/O
operations. When enabled, verify tasks will only be run during the time slots
scheduled for verifies. If a verify is taking place when the schedule is enabled,
it will be paused until the next scheduled time.
The priority of verify versus I/O operations is specified with 1..5, where 1 is
more resources and 5 the least. Setting this value to 1 implies fastest verify,
and 5 implies fastest I/O.
Enabling and disabling verify schedules is only for 9000 series controllerss,
however the verify rate (1..5) applies to all controllers.
/c
x
set selftest=enable|disable
[task=UDMA|SMART]
This command enables or disables all selftest tasks or a particular
selftest_task (UDMA or SMART).
Enabling and disabling selftest is only for 9000 series controllers. 7/8000
models have the same internal schedule, but it is not viewable or changeable.
Example:
//localhost> /c0 selftest=enable task=UDMA
enables UDMA selftest on controller c0.
Note: When enabling the verify schedule you must also remember to enable the
autoverify setting for the units to be verified. For more information see
“/cx/ux set autoverify=on|off” on page 70.
- CLI Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- About this CLI Guide 7
- Introduction to the 3ware 8
- Command Line Interface 8
- Supported Operating Systems 9
- Terminology 9
- Installing the 3ware CLI 10
- Run CLI 11
- Install Software. If the 11
- Working with 3ware CLI 12
- Scripting examples 14
- Conventions 15
- RAID Concepts 16
- Available RAID Configurations 17
- Single Disk 22
- Hot Spare 23
- Support for Over 2 Terabytes 25
- CLI Syntax Reference 26
- Syntax Overview 28
- /c1 add type=raid1 disk=0-1 29
- Shell Object Commands 30
- [force] 34
- Controller Object Commands 35
- /cx show achip 38
- /cx show allunitstatus 38
- /cx show autocarve 38
- /cx show autorebuild 39
- /cx show bios 39
- /cx show carvesize 40
- /cx show ctlbus 40
- /cx show driver 40
- /cx show drivestatus 40
- /cx show firmware 41
- /cx show memory 42
- /cx show model 42
- /cx show monitor 42
- /cx show numports 42
- /cx show numunits 43
- /cx show ondegrade 43
- /cx show pcb 43
- /cx show pchip 43
- /cx show serial 44
- /cx show spinup 44
- /cx show stagger 44
- /cx show unitstatus 44
- show alarms [reverse] 46
- show diag 46
- show phy 47
- show rebuild 47
- show selftest 49
- show verify 51
- Example: type=raid5 52
- For the 7/8000 55
- rescan [noscan] 56
- add rebuild= 58
- add verify= 59
- Setting Up a Verify Schedule 59
- add selftest= 60
- set selftest=enable 62
- [task=UDMA 62
- set carvesize=[1024..2048] 64
- set autorebuild=on 64
- start mediascan 66
- stop mediascan 66
- Unit Object Commands 67
- /cx/ux show autoverify 69
- /cx/ux show cache 69
- /cx/ux show identify 69
- /cx/ux show ignoreECC 69
- /cx/ux show initializestatus 70
- /cx/ux show name 70
- /cx/ux show qpolicy 70
- /cx/ux show rebuildstatus 70
- /cx/ux show serial 71
- /cx/ux show status 71
- /cx/ux show storsave 71
- /cx/ux show verifystatus 71
- RaidType 79
- Migration Process 82
- Example of splitting a mirror 83
- Example of capacity expansion 83
- Example of migrate output 83
- Port Object Commands 85
- attribute 86
- /cx/px show firmware 87
- /cx/px show identify 87
- /cx/px show lspeed 87
- /cx/px show model 87
- /cx/px show serial 88
- /cx/px show smart 88
- /cx/px show ncq 88
- remove [noscan] [quiet] 90
- Phy Object Commands 91
- BBU Object Commands 92
- /cx/bbu show serial 94
- /cx/bbu show status 94
- /bbu show all 95
- /cx/ex show controllers 98
- /cx/ex/ show diag=helptext 99
- /cx/ex show slots 99
- /cx/ex show fans 99
- /cx/ex show temp 99
- show all 100
- Example: 102
- Enclosure Object Commands 103
- Help Commands 104
- Help with attributes 105
- Command Logging 109
- Return Code 109
- If you type: 110
Relacionado con productos y manuales para Los controladores raid AMCC 3WARE 9590SE
Auto-meter 4359 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Für das Auto Auto-meter 4359.
Wir stellen 1 PDF-Handbücher Auto-meter 4359 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Auto meter 4359 Bedienungsanleitung (7 Seiten)
Marke: Auto-meter | Kategorie: For the car | Größe: 2.36 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Für das Auto Auto-meter
| Modelle | Dokumententyp |
|---|---|
| 4389 |
Bedienungsanleitung
Auto Meter 4389 User Manual,
4 Seiten
|
| 880017 |
Bedienungsanleitung
Auto Meter 880017 User Manual,
2 Seiten
|
| 4381 |
Bedienungsanleitung
Auto Meter 4381 User Manual,
7 Seiten
|
| 7963 |
Bedienungsanleitung
Auto Meter 7963 User Manual,
2 Seiten
|
| 7570 |
Bedienungsanleitung
Auto Meter 7570 User Manual,
2 Seiten
|
| 7955 |
Bedienungsanleitung
Auto Meter 7955 User Manual,
2 Seiten
|
| 3896 |
Bedienungsanleitung
Auto Meter 3896 User Manual,
2 Seiten
|
| 6834 |
Bedienungsanleitung
Auto Meter 6834 User Manual,
2 Seiten
|
| 2897 |
Bedienungsanleitung
Auto Meter 2897 User Manual,
4 Seiten
|
| 5896 |
Bedienungsanleitung
Auto Meter 5896 User Manual,
1 Seiten
|
| 4744 |
Bedienungsanleitung
Auto Meter 4744 User Manual,
2 Seiten
|
| 4776 |
Bedienungsanleitung
Auto Meter 4776 User Manual,
2 Seiten
|
| 4375 |
Bedienungsanleitung
Auto Meter 4375 User Manual,
4 Seiten
|
| 2304 |
Bedienungsanleitung
Auto Meter 2304 User Manual,
2 Seiten
|
| 233907 |
Bedienungsanleitung
Auto Meter 233907 User Manual,
2 Seiten
|
| 2306 |
Bedienungsanleitung
Auto Meter 2306 User Manual,
2 Seiten
|
| 2391 |
Bedienungsanleitung
Auto Meter 2391 User Manual,
2 Seiten
|
| 2360 |
Bedienungsanleitung
Auto Meter 2360 User Manual,
2 Seiten
|
| 2329 |
Bedienungsanleitung
Auto Meter 2329 User Manual,
2 Seiten
|
| 2312 |
Bedienungsanleitung
Auto Meter 2312 User Manual,
4 Seiten
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales