AMCC 3WARE 9590SE Guía de usuario Pagina 98
- Pagina / 110
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2. CLI Syntax Reference
92 3ware Serial ATA RAID Controller User Guide
Example:
//localhost> /c0/e0 show
Encl Status
---------------------------
/c0/e0 -
Fan Status State Step RPM Identify
------------------------------------------------------------
fan0 OK ON 1 2670 Off
fan1 OK ON 1 9500 Off
fan2 OK ON 1 8540 Off
fan3 OK ON 1 2830 Off
fan4 OK ON 1 9120 Off
fan5 OK ON 1 8330 Off
TempSensor Status Temperature Identify
--------------------------------------------------------
temp0 OK 41C(105F) Off
temp1 OK 38C(100F) Off
temp2 OK 34C(93F) Off
temp3 OK 38C(100F) Off
temp4 OK 38C(100F) Off
temp5 OK 34C(93F) Off
temp6 NOT-INSTALLED - Off
temp7 NOT-INSTALLED - Off
PowerSupply Status State Voltage Current Identify
---------------------------------------------------------------------------
pwrs0 OK on OK OK Off
pwrs1 OK on OK OK Off
Slot Status Port Identify
--------------------------------------------------
slot0 OK /c0/p0 Off
slot1 NO-DEVICE - Off
slot2 OK /c0/p1 Off
slot3 OK /c0/p2 Off
slot4 OK /c0/p3 Off
slot5 OK /c0/p4 Off
slot6 OK /c0/p5 Off
slot7 OK /c0/p6 Off
slot8 OK /c0/p7 Off
slot9 OK /c0/p8 Off
slot10 OK /c0/p9 Off
slot11 NO-DEVICE - Off
/cx/e
x
show
attribute
[
attribute
...]
This command is used with the 9690SA controller.
This command shows the current setting of the given attribute(s). One or
many attributes can be requested. An invalid attribute will terminate the loop.
Possible attributes are: controllers, slots, fans, and temp.
/cx/ex show controllers
This command lists the controller associated with enclosure /cx/ex.
Example:
//localhost> c0/e0 show controllers
c0/e0 Connected to /c0 controller
- CLI Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- About this CLI Guide 7
- Introduction to the 3ware 8
- Command Line Interface 8
- Supported Operating Systems 9
- Terminology 9
- Installing the 3ware CLI 10
- Run CLI 11
- Install Software. If the 11
- Working with 3ware CLI 12
- Scripting examples 14
- Conventions 15
- RAID Concepts 16
- Available RAID Configurations 17
- Single Disk 22
- Hot Spare 23
- Support for Over 2 Terabytes 25
- CLI Syntax Reference 26
- Syntax Overview 28
- /c1 add type=raid1 disk=0-1 29
- Shell Object Commands 30
- [force] 34
- Controller Object Commands 35
- /cx show achip 38
- /cx show allunitstatus 38
- /cx show autocarve 38
- /cx show autorebuild 39
- /cx show bios 39
- /cx show carvesize 40
- /cx show ctlbus 40
- /cx show driver 40
- /cx show drivestatus 40
- /cx show firmware 41
- /cx show memory 42
- /cx show model 42
- /cx show monitor 42
- /cx show numports 42
- /cx show numunits 43
- /cx show ondegrade 43
- /cx show pcb 43
- /cx show pchip 43
- /cx show serial 44
- /cx show spinup 44
- /cx show stagger 44
- /cx show unitstatus 44
- show alarms [reverse] 46
- show diag 46
- show phy 47
- show rebuild 47
- show selftest 49
- show verify 51
- Example: type=raid5 52
- For the 7/8000 55
- rescan [noscan] 56
- add rebuild= 58
- add verify= 59
- Setting Up a Verify Schedule 59
- add selftest= 60
- set selftest=enable 62
- [task=UDMA 62
- set carvesize=[1024..2048] 64
- set autorebuild=on 64
- start mediascan 66
- stop mediascan 66
- Unit Object Commands 67
- /cx/ux show autoverify 69
- /cx/ux show cache 69
- /cx/ux show identify 69
- /cx/ux show ignoreECC 69
- /cx/ux show initializestatus 70
- /cx/ux show name 70
- /cx/ux show qpolicy 70
- /cx/ux show rebuildstatus 70
- /cx/ux show serial 71
- /cx/ux show status 71
- /cx/ux show storsave 71
- /cx/ux show verifystatus 71
- RaidType 79
- Migration Process 82
- Example of splitting a mirror 83
- Example of capacity expansion 83
- Example of migrate output 83
- Port Object Commands 85
- attribute 86
- /cx/px show firmware 87
- /cx/px show identify 87
- /cx/px show lspeed 87
- /cx/px show model 87
- /cx/px show serial 88
- /cx/px show smart 88
- /cx/px show ncq 88
- remove [noscan] [quiet] 90
- Phy Object Commands 91
- BBU Object Commands 92
- /cx/bbu show serial 94
- /cx/bbu show status 94
- /bbu show all 95
- /cx/ex show controllers 98
- /cx/ex/ show diag=helptext 99
- /cx/ex show slots 99
- /cx/ex show fans 99
- /cx/ex show temp 99
- show all 100
- Example: 102
- Enclosure Object Commands 103
- Help Commands 104
- Help with attributes 105
- Command Logging 109
- Return Code 109
- If you type: 110
Relacionado con productos y manuales para Los controladores raid AMCC 3WARE 9590SE
(302 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales